LOADING...

2008 BUELL-FIREBOLT-SERVICE-MANUAL FILETYPE PDF

View and Download Buell XB Series service manual online. XB Series Motorcycle pdf manual download. See a Buell service manual for proper torque values. Aftermarket . Typical Buell V.I.N.: Ulysses Models Ignition System: XB Models. ITEM. DATA. T+ .com/

Author: Jusho Zolomuro
Country: Yemen
Language: English (Spanish)
Genre: Automotive
Published (Last): 2 April 2018
Pages: 18
PDF File Size: 9.35 Mb
ePub File Size: 19.21 Mb
ISBN: 887-1-20151-676-7
Downloads: 83349
Price: Free* [*Free Regsitration Required]
Uploader: Akinorn

Disconnect fuel pump connection and remove connector sm from subframe tail assembly. Rotate crankshaft until all timing marks 7, 8 are aligned as shown.

Buell-firebolt-servuce-manual Header XB Service: Gasket is part of the piston jet assembly.

Ulysses Models om 1. When removing and installing the left air scoop, the alternator and voltage regulator harnesses and connections are secured Remove three engine shroud air scoop fasteners 5.

Replace cables not meeting resistance Resistor-type high-tension spark plug cables have a carbon- specifications. Remove “V” bracket buel-firebolt-service-manual and fasteners 3 from main frame.

Buell Firebolt Service Manual

Hold footpeg 10controlling spring, to footpeg mount 1. Loosen fasteners on right and left side of headlamp housing to adjust the horizontal alignment. The repair instructions contained in this section are divided into three major service areas accordingly. Tighten jam nut 3 against adjuster 4. Air cleaner cover 3. Rear Isolator Bolt Figure Separate the adjusting screw 8 from the bearing 7 and release plate 5.

  LEGO 8049 BAUANLEITUNG PDF

The bottom of the preload adjuster is round with two flat sides so a wrench 2 can be used to Wheel fastener Figure NOTE sm In next step, make sure wire is in cutout portion slot of socket to prevent damage. Remove fastener 10 securing the side case bracket 11 to the back of the passenger footrest support bracket. Depress ratchet arms 3 in order to clear the shifter drum and remove shifter shaft assembly from left crankcase half.

Buell XB 2008 Series Service Manual

Remove front caliper bleeder valve cap and install a length of plastic tubing over valve 1. Hold damper rod assembly jamnut 3 and remove fork sm cap 1. Removing Piston Pin Circlip Figure Bank angle sensor 2. Rear caliper pin plug 4. Replace complete bearing assembly if any component is damaged. Tighten ET sensor to in-lbs Remove pedal fastener 4. To ensure proper reservoir mounting, tempor- arily place upper body work onto tail section and adjust reser- voir placement so adjuster screw 1 aligns with alignment hole 2.

Turn the engine cut-off switch to RUN. Remove body work fasteners 2. Disconnect the two connectors [45] from license plate lamp harness 2. On the pin side of the connector, tangs are positioned at the bottom of each cavity, so the slot in the pin terminal on the side opposite the crimp tails must face downward.

  JACK MCDEVITT ODYSSEY PDF

Failure to center the spacer could cause the bearing not to pull in straight. Remove and discard retaining ring 5. NOTE sm Fuel line is installed under engine connector portion of wire harness.

2008 Buell XB Models Service Repair Workshop Manual DOWNLOAD

If necessary, disassemble adjusting screw assembly. Removal end of bearing tool 2. To maintain the safety, dependability, and emission and noise control performance, it is essential that the procedures, specifications and service instructions in this manual are followed.

To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative – battery Figure Buuell-firebolt-service-manual Firebolt models, route transmis- NOTES sion vent line up through left side of frame exiting Vehicle should be placed onto the lift with rear tire in the under the rear master cylinder under the rider’s seat.

Replace housing buell-firebolt-servlce-manual any of these condi- tions are found.

Thin steel strip Figure To prevent leaks, lubricate the o-rings before installation. Tamper-resistant Torx fasteners 2 8.